|
KEY
|
TITLE OF THE PAPER
|
AUTHORS' NAMES
|
| 040401 |
Exhaust
Analysis and Performance of a Single Cylinder Diesel Engine Run on
Dual Fuels |
V
P Sethi, NM
K S Salaria, M
|
| 040402 |
Exhaust
Gas Simulation |
Dr
N V Deshpande, F
M K Madnani, NM
A Joshi, NM
A Gupta, NM
|
| 040403 |
Development
of Asbestos Free Brake Pad |
Dr
N Chand, NM
Dr S A R Hashmi, M
S Lomash, F
A Naik, NM
|
| 040404 |
Simple
Discharge Relations for Sharp-crested Rectangular Weir and
Right-angled Triangular Weir at Low Heads |
D
Mitra, NM
A Mazumdar, M |
| 040405 |
Performance
Characteristics of Hole-entry Hybrid Journal Bearing of Different
Configurations |
V
Kumar, NM
J Aggarwal, NM
S K Ghai, NM
|
| 040406 |
A
New Generation Rolling-element Bearing -- An Investigation |
Dr
H Prashad, F |
| 040407 |
Performance
Evaluation of a Reverse-flow Gas Turbine Combustor |
Dr
M D Agarwal, M
Dr S Bharani, M |
|
JULY 2004 ISSUE
|
|
KEY |
TITLE OF THE PAPER |
AUTHORS' NAMES |
|
070401 |
Experimental Studies on Energy
Appropriation in a Single Cylinder Diesel Engine |
P Ravi Kumar, NM
P N Srinivas, NM
Dr J E B Nelson, NM
Dr S S Rao, NM
|
|
070402 |
Numerical Study of Interaction of Surface
Radiation with Conjugate Convection from a Vertical Plate with
Multiple Discrete Heat Sources |
Dr C G Rao, A
K Kumar, NM
K Bhadraiah, NM
|
|
070403 |
A Finite Element Thermal Model for Axi-symmetric
Cold and Hot Extrusion using Upper Bound Technique |
Dr S Kumar, NM
S K Prasad, NM
|
|
070404 |
Analysis of Carbon Epoxy Shaft in
Aerostatic Conical Journal Bearings -- No Rotational Case |
R B Ingle, NM
Dr B B Ahuja, M
S M Joshi, AM
|
|
070405 |
Wheel Lift-off and Ride Comfort of
Three-wheeled Vehicle over Bump |
T R Gawade, NM
Dr S Mukherjee, NM
Prof D Mohan, M
|
|
070406 |
Prediction of Defects in Anti-friction
Bearings using Vibration Signal Analysis |
M Amarnath, NM
R Srinidhi, NM
A Ramachandra, M
S B Kandagal, M
|
|
OCTOBER 2004 ISSUE |
|
KEY |
TITLE OF THE PAPER |
AUTHORS' NAMES |
|
100401 |
Assessment of Machine Generated Noise with
Maintenance of Various Heavy Earthmoving Machinery |
H Vardhan, AM
N C Karmakar, M
Y V Rao, M
|
|
100402 |
Five-bar Motion and Path Generators with
Variable Topology |
Dr S S Balli, M
|
|
100403 |
Crack Opening Behaviour Prediction of Crack
Growth and Fatigue Life under Mixed Mode Cyclic Loading in 2024-T3
Al Alloy |
P C Gope, NM
S P Sharma, NM
Dr B Kumar, NM
|
|
100404 |
Comparison of the Effectiveness of Rupture
Disc Design using FEM |
D V R Murty, NM
Dr K N Rao, F
Dr Y B Rao, NM
|
|
100405 |
Flow Analysis of SI Engine Air Intake
System during Idling |
J Suresh Kumar, NM
Prof V Ganesan, M
|
|
100406 |
Dynamic Modification of Machine Tool
Structure |
Prof R K Srivastava, F
V Pandey, NM
|
|
100407 |
Thermo-hydrodynamic Analysis of Steadily
Loaded Journal Bearings |
K Jagannath, M
Dr K Raghunandana, M
Dr A M Chincholkar,
M
|
|
100408 |
Distributed Control Architecture for
Semi-autonomous Mobile Robots |
Dr N P Mahalik, NM
|
|
100409 |
Non-destructive Evaluation Techniques for
Condition Monitoring of Components and Plants |
Dr C K Mukhopadhyay, NM
Dr T Jayakumar, NM
Dr Baldev Raj, F
|
|
JANUARY 2005 ISSUE |
|
KEY |
TITLE OF THE PAPER |
AUTHORS' NAMES |
|
|
|
|
|
